Thursday, August 31, 2006
New Version of Blogger
Seems like there is a new version of blogger. I'm going to port over and see how it goes. First let me copy all my configs ;-)
Cisco port analyzer SPAN feature
If you are on a Cisco network and need to monitor network traffic or filtering you'll need to setup SPANning on one of your switches. Here is Cisco's Configuring the Catalyst Switched Port Analyzer (SPAN) Feature page.
In a nut shell what is happening is that you are copying traffice from one port (sourse) to another (destination) for monitoring. So lets say you have a firewall on port 0/1 and you want to capture and filter all the web traffic what you would do is plug you monitor into another port say port 0/24. Now you would need to copy all traffic from port 0/1 to 0/24. to do so you'd have to setup a SPAN or monitor session.
#config t
(config)#monitor session 1 source interface fastethernet 0/1
(config)#monitor session 1 destination interface fastethernet 0/24 both
(config)#end
The both at the end of the second command means that this port is bidirectional rx and tx.
Enjoy!
In a nut shell what is happening is that you are copying traffice from one port (sourse) to another (destination) for monitoring. So lets say you have a firewall on port 0/1 and you want to capture and filter all the web traffic what you would do is plug you monitor into another port say port 0/24. Now you would need to copy all traffic from port 0/1 to 0/24. to do so you'd have to setup a SPAN or monitor session.
#config t
(config)#monitor session 1 source interface fastethernet 0/1
(config)#monitor session 1 destination interface fastethernet 0/24 both
(config)#end
The both at the end of the second command means that this port is bidirectional rx and tx.
Enjoy!
Web filtering
Another one of my tasks is to make sure web filtering is in place. Can't have users going to Adult sites on the job or doing other non work related activities. The product we use is Surf Control Web Filter. When I started here over 5 years ago this is what was in place but it was installed on the Windows NT4.0 firewall (yes an NT4.0 firewall) at the time. It was suppose to go hand and hand with Checkpoint Firewall for NT. It worked OK. But as many people know that NT4.0 was a system hog in itself then putting Checkpoint on it and Surf Control on top of that put a strain on the server. So after a while of dealing with that crappy box and all the problems I've had with it (firewall crashed and I had to get a non windows firewall). Anyway I've install Surf Control on it's own server and got it filtering the web traffic.
The installation went OK you need either an SQL server to talk to or MSDE on the box itself. I went to MSDE route. I want this box to depend on itself only. At the time since our switched didn't allow rx tx on the SPAN port (or maybe I just didn't spend enough time trying to figure that out) we used a HUB since that allowed writeback. What am I talking about? In order for Surf Control to effectively block sites it has to capture packets and determine it's nature and either let it go or put a block on it sending a message to the users screen. This is what I am talking about when I say writeback or rx and tx. Since our network upgrade I was able to toss out that HUB and properly configure my new Cisco 4506 to SPAN with rx, tx. So now Surf is blocking site on a switch like it should.
The product itself has nice features. Realtime logging, categorization of sites, reporting of user usage, most visited site in a given time etc. It also integrates with Active Directory (now). But the product is a little flaky and buggy. It takes some time to figure out and you'll find yourself on their knowledgebase very often. I guess I've built up a tolerance for it's buggyness and just cope with it. After all I do know how to get it to work.
The installation went OK you need either an SQL server to talk to or MSDE on the box itself. I went to MSDE route. I want this box to depend on itself only. At the time since our switched didn't allow rx tx on the SPAN port (or maybe I just didn't spend enough time trying to figure that out) we used a HUB since that allowed writeback. What am I talking about? In order for Surf Control to effectively block sites it has to capture packets and determine it's nature and either let it go or put a block on it sending a message to the users screen. This is what I am talking about when I say writeback or rx and tx. Since our network upgrade I was able to toss out that HUB and properly configure my new Cisco 4506 to SPAN with rx, tx. So now Surf is blocking site on a switch like it should.
The product itself has nice features. Realtime logging, categorization of sites, reporting of user usage, most visited site in a given time etc. It also integrates with Active Directory (now). But the product is a little flaky and buggy. It takes some time to figure out and you'll find yourself on their knowledgebase very often. I guess I've built up a tolerance for it's buggyness and just cope with it. After all I do know how to get it to work.
Monday, August 28, 2006
Copying LARGE amounts of data
In the industry I work in we have LARGE files and HUGE folders to copy from one location to the next. I'm talking about hundreds of Gigs. Weather it be from production to production space or production to archive. We want to be sure being in a Windows environment that the file copy doesn't bomb out (good old copy, paste). I use Robocopy to handle all my copying needs. Robocopy is an old tool part of Microsoft Resource kit.
This site (http://www.ss64.com/nt/robocopy.html) has beginner information about robocopy. Once I started using robocopy years ago I never stopped. You can also use Xcopy to achieve the same results.
This site (http://www.ss64.com/nt/robocopy.html) has beginner information about robocopy. Once I started using robocopy years ago I never stopped. You can also use Xcopy to achieve the same results.
The power of the SAN
One of our departments needed space last week. Lots of if and out of nowhere too. So think about a strategy for about 15 mins b/c we really didn't want to do what took us only 5 mins to think of. Anyway it came back to putting their data on the SAN. Luckily we have SATA drive to use so we created a 600GB LUN on the SAN put it in a storage group with it's host and whalah!!! 600GB available to them like that. It's easy for us to do all this storage shuffling now b/c we have our infrastructure in place. Fiber channel switches, HBA's in each server emc SAN and lots of drive space ;)
Need help building out your infrastructure for a SAN solution hit me up :D
Need help building out your infrastructure for a SAN solution hit me up :D
Login scripts
To manage who gets what and how on the workstations we use login scritps. In our Windows 2003 AD environment you can use group policy but we have been using kixtart and login.bat ever since NT4.0. It works that damn good. In my example my users are in group ABC & XYZ and will get mapped drives from certain files servers and printers from certain print servers.
Install the kixtart files to your sysvol direcory of your domain controller. By now they should have a template for you to follow (not sure I've haven't upgrade it in years). Anyway in AD under the user account profile tab in the section for login script put login.bat
In the sysvol folder of you domain controller create a text file add this entry to it
@echo off
%0\..\Kix32.exe kick.scr
then save it as login.bat When the user logs in they will be calling this file. This file will then execute Kixtart and call kick.scr
Kick.scr is the srcipt that does all the mapping based on where the user lies in AD. Here is an simple versio of the Kick.scr sript that I use. I have most things (; commented out ; = comment in the begining of each line)
;*****ABC Group*********************************************
If Ingroup ("ABC")
;Deploy intranet page to IE This will make their IE default to the company intranet page all the time.
writevalue("HKEY_CURRENT_USER\Software\Microsoft\Internet Explorer\Main","Start Page","http://intranet_address_here","REG_SZ")
;Map Network Drives
;Example this will give all users in group ABC a network map for ABCresources on 'fileserver01' as a (Z) drive
use z: "\\fileserver01\ABCresources"
; use i: "\\servername\share"
; use j: "\\servername\share"
; use k: "\\servername\share"
; use l: "\\servername\share"
; use m: "\\servername\share"
; use n: "\\servername\share"
; use o: "\\servername\share"
; use p: "\\servername\share"
; use p: "\\servername\share"
; use r: "\\servername\share"
;Map to Network Printers
;Example this will give all users in group ABC a network printer called ABCgroup_color_printer from printserver1
addprinterconnection ("\\printserver1\ABCgroup_color_printer")
; addprinterconnection ("\\print_server_name\printer_name")
; addprinterconnection ("\\print_server_name\printer_name")
; addprinterconnection ("\\print_server_name\printer_name")
; addprinterconnection ("\\print_server_name\printer_name")
; addprinterconnection ("\\print_server_name\printer_name")
; addprinterconnection ("\\print_server_name\printer_name")
; addprinterconnection ("\\print_server_name\printer_name")
; addprinterconnection ("\\print_server_name\printer_name")
; addprinterconnection ("\\print_server_name\printer_name")
;to delete a printer connection
;Example to delete the ABCgroup_color_printer from the group
delkey ("HKEY_CURRENT_USER\Printers\Connections\,,printserver1,ABCgroup_color_printer")
; delkey ("HKEY_CURRENT_USER\Printers\Connections\,,print_server_name,printer_name")
; delkey ("HKEY_CURRENT_USER\Printers\Connections\,,print_server_name,printer_name")
EndIf
;*******************************************************************
;*************XYZ Group*********************************************
If Ingroup ("XYZ")
;Deploy intranet page to IE
writevalue("HKEY_CURRENT_USER\Software\Microsoft\Internet Explorer\Main","Start Page","http://intranet_address_here","REG_SZ")
;Map Network Drives
; use i: "\\servername\share"
; use j: "\\servername\share"
; use k: "\\servername\share"
; use l: "\\servername\share"
; use m: "\\servername\share"
; use n: "\\servername\share"
; use o: "\\servername\share"
; use p: "\\servername\share"
; use p: "\\servername\share"
; use r: "\\servername\share"
;Map to Network Printers
; addprinterconnection ("\\print_server_name\printer_name")
; addprinterconnection ("\\print_server_name\printer_name")
; addprinterconnection ("\\print_server_name\printer_name")
; addprinterconnection ("\\print_server_name\printer_name")
; addprinterconnection ("\\print_server_name\printer_name")
; addprinterconnection ("\\print_server_name\printer_name")
; addprinterconnection ("\\print_server_name\printer_name")
; addprinterconnection ("\\print_server_name\printer_name")
; addprinterconnection ("\\print_server_name\printer_name")
; addprinterconnection ("\\print_server_name\printer_name")
;to delete a printer connection
; delkey ("HKEY_CURRENT_USER\Printers\Connections\,,print_server_name,printer_name")
; delkey ("HKEY_CURRENT_USER\Printers\Connections\,,print_server_name,printer_name")
; delkey ("HKEY_CURRENT_USER\Printers\Connections\,,print_server_name,printer_name")
EndIf
;*******************************************************************
So in this sample script I have two groups ABC & XYZ this represents the different groups in AD. This is one way of using the script. There are many ways to get the job done.
Install the kixtart files to your sysvol direcory of your domain controller. By now they should have a template for you to follow (not sure I've haven't upgrade it in years). Anyway in AD under the user account profile tab in the section for login script put login.bat
In the sysvol folder of you domain controller create a text file add this entry to it
@echo off
%0\..\Kix32.exe kick.scr
then save it as login.bat When the user logs in they will be calling this file. This file will then execute Kixtart and call kick.scr
Kick.scr is the srcipt that does all the mapping based on where the user lies in AD. Here is an simple versio of the Kick.scr sript that I use. I have most things (; commented out ; = comment in the begining of each line)
;*****ABC Group*********************************************
If Ingroup ("ABC")
;Deploy intranet page to IE This will make their IE default to the company intranet page all the time.
writevalue("HKEY_CURRENT_USER\Software\Microsoft\Internet Explorer\Main","Start Page","http://intranet_address_here","REG_SZ")
;Map Network Drives
;Example this will give all users in group ABC a network map for ABCresources on 'fileserver01' as a (Z) drive
use z: "\\fileserver01\ABCresources"
; use i: "\\servername\share"
; use j: "\\servername\share"
; use k: "\\servername\share"
; use l: "\\servername\share"
; use m: "\\servername\share"
; use n: "\\servername\share"
; use o: "\\servername\share"
; use p: "\\servername\share"
; use p: "\\servername\share"
; use r: "\\servername\share"
;Map to Network Printers
;Example this will give all users in group ABC a network printer called ABCgroup_color_printer from printserver1
addprinterconnection ("\\printserver1\ABCgroup_color_printer")
; addprinterconnection ("\\print_server_name\printer_name")
; addprinterconnection ("\\print_server_name\printer_name")
; addprinterconnection ("\\print_server_name\printer_name")
; addprinterconnection ("\\print_server_name\printer_name")
; addprinterconnection ("\\print_server_name\printer_name")
; addprinterconnection ("\\print_server_name\printer_name")
; addprinterconnection ("\\print_server_name\printer_name")
; addprinterconnection ("\\print_server_name\printer_name")
; addprinterconnection ("\\print_server_name\printer_name")
;to delete a printer connection
;Example to delete the ABCgroup_color_printer from the group
delkey ("HKEY_CURRENT_USER\Printers\Connections\,,printserver1,ABCgroup_color_printer")
; delkey ("HKEY_CURRENT_USER\Printers\Connections\,,print_server_name,printer_name")
; delkey ("HKEY_CURRENT_USER\Printers\Connections\,,print_server_name,printer_name")
EndIf
;*******************************************************************
;*************XYZ Group*********************************************
If Ingroup ("XYZ")
;Deploy intranet page to IE
writevalue("HKEY_CURRENT_USER\Software\Microsoft\Internet Explorer\Main","Start Page","http://intranet_address_here","REG_SZ")
;Map Network Drives
; use i: "\\servername\share"
; use j: "\\servername\share"
; use k: "\\servername\share"
; use l: "\\servername\share"
; use m: "\\servername\share"
; use n: "\\servername\share"
; use o: "\\servername\share"
; use p: "\\servername\share"
; use p: "\\servername\share"
; use r: "\\servername\share"
;Map to Network Printers
; addprinterconnection ("\\print_server_name\printer_name")
; addprinterconnection ("\\print_server_name\printer_name")
; addprinterconnection ("\\print_server_name\printer_name")
; addprinterconnection ("\\print_server_name\printer_name")
; addprinterconnection ("\\print_server_name\printer_name")
; addprinterconnection ("\\print_server_name\printer_name")
; addprinterconnection ("\\print_server_name\printer_name")
; addprinterconnection ("\\print_server_name\printer_name")
; addprinterconnection ("\\print_server_name\printer_name")
; addprinterconnection ("\\print_server_name\printer_name")
;to delete a printer connection
; delkey ("HKEY_CURRENT_USER\Printers\Connections\,,print_server_name,printer_name")
; delkey ("HKEY_CURRENT_USER\Printers\Connections\,,print_server_name,printer_name")
; delkey ("HKEY_CURRENT_USER\Printers\Connections\,,print_server_name,printer_name")
EndIf
;*******************************************************************
So in this sample script I have two groups ABC & XYZ this represents the different groups in AD. This is one way of using the script. There are many ways to get the job done.
Monday, August 21, 2006
Server room over heat
Over the weekend the AC unit in our server room went out. It happened sometime late Friday night. The room being so small and full with other crap caused the room to heat up in a matter of minutes. As a result of this the servers started shutting themselves down.
We have a dedicated AC unit like any other server room would have. The problem is that the unit is connected to our building central fire until. Something went wrong with the fire command unit last week as there were tests and the HVAC repair guys in most of the week fixing other related issue. Over the weekend the fire command unit cut the power to the AC units in the building. This caused what could have been a nasty chair reaction to occur. Resulting in me and other coworkers racing in on Saturday morning.
How did we know something was wrong? The internet connection to the office went out. The firewall shutdown. So no email notifications could go out. We found out b/c one of us was trying to work from home on Saturday morning and noticed the VPN down, OWA down, ftp down. So I had a pretty interesting weekend. Now to get to the bottom of WTF the building is up to with their fire command unit. In the past 2 weeks our dedicated AC unit for our server room went out 3 times now and the funny thing is it's not even all that hot here in NY. I could understand if this was the week we had a heatwave but it's not. It's in the low 80's when all of this as been happening. So now I am looking into a Sensaphone 1400. Someone wants to charge us $4800 for it. I know nothing about this device but from the description it looks pretty good.
Here is what we are doing to ensure the room stays cool right now LOL!!!

They all will be removed when we are sure the building has their act together.
We have a dedicated AC unit like any other server room would have. The problem is that the unit is connected to our building central fire until. Something went wrong with the fire command unit last week as there were tests and the HVAC repair guys in most of the week fixing other related issue. Over the weekend the fire command unit cut the power to the AC units in the building. This caused what could have been a nasty chair reaction to occur. Resulting in me and other coworkers racing in on Saturday morning.
How did we know something was wrong? The internet connection to the office went out. The firewall shutdown. So no email notifications could go out. We found out b/c one of us was trying to work from home on Saturday morning and noticed the VPN down, OWA down, ftp down. So I had a pretty interesting weekend. Now to get to the bottom of WTF the building is up to with their fire command unit. In the past 2 weeks our dedicated AC unit for our server room went out 3 times now and the funny thing is it's not even all that hot here in NY. I could understand if this was the week we had a heatwave but it's not. It's in the low 80's when all of this as been happening. So now I am looking into a Sensaphone 1400. Someone wants to charge us $4800 for it. I know nothing about this device but from the description it looks pretty good.
Here is what we are doing to ensure the room stays cool right now LOL!!!
They all will be removed when we are sure the building has their act together.
Cisco IPT installation update
So what have I been up to?
Well, we rolled out the cisco phone system. The system got configured and is up and running without any problems. We are still using our old PBX and only a hand full of users are on the new system now. I am trying to make this as smooth as possible but have run into one snag.
On the old system we use 4 digit extensions on the Cisco system we use 4 digit extension. So what the issue? Well the, T1 connection between the old and new system require anyone on the old PBX to dial an access code to connect anyone on the Cisco system. So if I am on the old system I have to dial an access number say (6) then the 4 digit extension. This is going to be a huge hassle. We are going to have to tell all the users to enter an extra digit to speak to the users on the new system. But if you are on the new system you don't have to dial that extra digit. All kinds of confusion can happen.
So why can't we setup the systems to hide a digit so it seems like no matter what system a user is on they will only dial 4 digits? Problem is that our PBS was never upgraded though out the years and we do not have an option for coordinated dial plan (CDP). This will allow the PBX to hide or insert a digit right after the access number is pressed. So if the access number is (6) and the extension to the new system is 7560 the PBX will be smart enough to insert the (7) at the beginning of the extension right after you press the access code number of (6). This also brings up other issues down the road as well.
Why can't we do this from the Cisco end then? Well, we can but the PBX will only issue 4 digits. It will only allow use to dial 4 digits once their is a dial tone. If the PBX allowed us to issues only 3 digits we could easily have the Cisco system add a digit. How do I know??? We already got this to work. WHAT? Yes we got this to work then the very next day we come in and it's not working. WTF!!!!!!!! We call in consultants and a PBX guy. The PBX guys are saying we have to spend 30K to upgrade the system just to allows coordinated dial plans (CDP). Screw them. We're not going to spend 30K and will only keep the PBX for 6 months until we get everyone on the Cisco system.
Well, we rolled out the cisco phone system. The system got configured and is up and running without any problems. We are still using our old PBX and only a hand full of users are on the new system now. I am trying to make this as smooth as possible but have run into one snag.
On the old system we use 4 digit extensions on the Cisco system we use 4 digit extension. So what the issue? Well the, T1 connection between the old and new system require anyone on the old PBX to dial an access code to connect anyone on the Cisco system. So if I am on the old system I have to dial an access number say (6) then the 4 digit extension. This is going to be a huge hassle. We are going to have to tell all the users to enter an extra digit to speak to the users on the new system. But if you are on the new system you don't have to dial that extra digit. All kinds of confusion can happen.
So why can't we setup the systems to hide a digit so it seems like no matter what system a user is on they will only dial 4 digits? Problem is that our PBS was never upgraded though out the years and we do not have an option for coordinated dial plan (CDP). This will allow the PBX to hide or insert a digit right after the access number is pressed. So if the access number is (6) and the extension to the new system is 7560 the PBX will be smart enough to insert the (7) at the beginning of the extension right after you press the access code number of (6). This also brings up other issues down the road as well.
Why can't we do this from the Cisco end then? Well, we can but the PBX will only issue 4 digits. It will only allow use to dial 4 digits once their is a dial tone. If the PBX allowed us to issues only 3 digits we could easily have the Cisco system add a digit. How do I know??? We already got this to work. WHAT? Yes we got this to work then the very next day we come in and it's not working. WTF!!!!!!!! We call in consultants and a PBX guy. The PBX guys are saying we have to spend 30K to upgrade the system just to allows coordinated dial plans (CDP). Screw them. We're not going to spend 30K and will only keep the PBX for 6 months until we get everyone on the Cisco system.
Monday, August 14, 2006
What once was
Well since sloppy wiring seem to be flying around the net as of late I'll proudly display what my core rack USE to look like ;)
This is what happens when you have to scramble for space for a parallel network installation.
Can anyone spot the hanging switch???
How about the cliff jumping Linksys???
What about the DMZ that dubbed as a perch???
This is what happens when you have to scramble for space for a parallel network installation.
Can anyone spot the hanging switch???
How about the cliff jumping Linksys???
What about the DMZ that dubbed as a perch???
Thursday, August 03, 2006
The light
Just gimmie the light and pass the...
To the naked eye the light from a connected fiber cable is red but to the camera's eye it's white.
Here is the light from the gig port once an LC connector SX transceiver is installed. (these little bastards can get expensive)


Here is the LC/SC fiber cable this is the LC side.


You notice that only one side is lit that's b/c one side sends and one side receives data.
To the naked eye the light from a connected fiber cable is red but to the camera's eye it's white.
Here is the light from the gig port once an LC connector SX transceiver is installed. (these little bastards can get expensive)
Here is the LC/SC fiber cable this is the LC side.
You notice that only one side is lit that's b/c one side sends and one side receives data.
Monday, July 31, 2006
A peek inside the DHCP server
Here is what the DHCP server looks like for a network with VLANs on every floor and a VOIP system.

From the pic you can see all the scopes created. What is happening here as I mentioned before is that each floor is it own VLAN and each VLAN gets their IP from the scope that it's associated with. Remember that IP helper address I told you about (10.100.1.22) well this is the server.
You will also notice more than half my scopes are inactive. This is b/c the 12th floor isn't online as of yet. Also the other scopes are for the IP phones for each floor too. Those aren't rolled out yet either. Yes the phones need a scope too. They will have IP's as well.
For the ones that don't know the IP phone plugs into a standard RJ45 jack (the network jack)and your PC plugs into the phone. The IP phone is also a switch.
Bottom of a Cisco IP phone
10/100 SW goes into your network jack
10/100 PC connects to your PC
The AC power port you do not need if you have power over ethernet (PoE). Your access switches will power your IP phones.
From the pic you can see all the scopes created. What is happening here as I mentioned before is that each floor is it own VLAN and each VLAN gets their IP from the scope that it's associated with. Remember that IP helper address I told you about (10.100.1.22) well this is the server.
You will also notice more than half my scopes are inactive. This is b/c the 12th floor isn't online as of yet. Also the other scopes are for the IP phones for each floor too. Those aren't rolled out yet either. Yes the phones need a scope too. They will have IP's as well.
For the ones that don't know the IP phone plugs into a standard RJ45 jack (the network jack)and your PC plugs into the phone. The IP phone is also a switch.
Bottom of a Cisco IP phone
10/100 SW goes into your network jack
10/100 PC connects to your PC
The AC power port you do not need if you have power over ethernet (PoE). Your access switches will power your IP phones.
Friday, July 28, 2006
Fiber cables and IPT stuff
I'm using three types of connections in my network. SC/SC, LC/SC, SC/SC.
SC/SC

The SC/SC cables go from the fiber panel to the core switch. They connect to one of the ports on the gig module on the 4506. This would be your backbone cable in the data center (depending on setup).
LC/SC

The LC/SC cable is from the fiber patch panel to an access switch. Or from a core switch to an access switch or from an old access witch to a newer model 3500xl to 3560 for example.
LC/LC

The LC/LC cables connect two access switch's together via the gig ports (depending on setup).
Here is my fiber panel in my data center. These go up to all my floors.

Each floor as six pair or 12 strands. Whoever installed this before my time did an excellent job with leaving room for growth. If we have to pull new fiber it would have cost us tens-of-thousands of dollars.

A fiber panel on my 15th floor. We are only using two pair. (one is unplugged)

(someone forgot to dust)
PBX and Cisco

Cisco on the cart next to PBX

Call manager on top
3560 switch below
2811 gateway router
2851 gateway router

The red cable represents the T1 link. This is the line that will connect the old PBX to the new Cisco system.

This rack will house the CM the Unity connect server the gateway along with a few UPS'. We will also get another CM in a few months when we get more phones.
SC/SC
The SC/SC cables go from the fiber panel to the core switch. They connect to one of the ports on the gig module on the 4506. This would be your backbone cable in the data center (depending on setup).
LC/SC
The LC/SC cable is from the fiber patch panel to an access switch. Or from a core switch to an access switch or from an old access witch to a newer model 3500xl to 3560 for example.
LC/LC
The LC/LC cables connect two access switch's together via the gig ports (depending on setup).
Here is my fiber panel in my data center. These go up to all my floors.
Each floor as six pair or 12 strands. Whoever installed this before my time did an excellent job with leaving room for growth. If we have to pull new fiber it would have cost us tens-of-thousands of dollars.
A fiber panel on my 15th floor. We are only using two pair. (one is unplugged)
(someone forgot to dust)
PBX and Cisco
Cisco on the cart next to PBX
Call manager on top
3560 switch below
2811 gateway router
2851 gateway router
The red cable represents the T1 link. This is the line that will connect the old PBX to the new Cisco system.
This rack will house the CM the Unity connect server the gateway along with a few UPS'. We will also get another CM in a few months when we get more phones.
Monday, July 24, 2006
This weeks agenda
-Call manager install. I'll blog that for sure.
-VLANs configured for QoS (may or may not happen this week)
-Nortel option 61 T1 card being installed in our PBX (this is to connect to the Cisco system since we are doing the hybrid approach). It's a T1 between both systems to be exact. Also the card for the PBX will require downtime. Damn it's a really old PBX system too...
-My gig E modules need to be installed but I was told this may require downtime. So a 7am installation is deffinitely on the agenda.
-New floor data cabling and some power install. Two separate vendors I have to coordinate with for this too. They are union guys too so they tend to drag jobs out.
-Very busy week.
-VLANs configured for QoS (may or may not happen this week)
-Nortel option 61 T1 card being installed in our PBX (this is to connect to the Cisco system since we are doing the hybrid approach). It's a T1 between both systems to be exact. Also the card for the PBX will require downtime. Damn it's a really old PBX system too...
-My gig E modules need to be installed but I was told this may require downtime. So a 7am installation is deffinitely on the agenda.
-New floor data cabling and some power install. Two separate vendors I have to coordinate with for this too. They are union guys too so they tend to drag jobs out.
-Very busy week.
Friday, July 21, 2006
My current VLAN setup
With our dual core setup we are fully redundant. All access layer switches (the ones on the floors and usually in pairs) have a connection to each core switch. The way this works physically is by connecting one fiber cable to one gig port all the way down to one core switch and one port on the second access switch to the other core in our data center. Then connecting one of the gig ports on the access switch to one port on the other access switch. The two cores are also connected to each other. Picture all four switches in a circle holding hands.

In the core we have our VLANs. As I explained in a past post each floor is a VLAN. The only way to make this physical redundancy work is to set it up virtually in the core. We have two core switches A&B. One is the root and the other is the standby. If the root core fails for whatever reason the standby is there. The setup on the core for redundant VLANs looks like this.
switch A
interface Vlan30
description CLIENT_FLOOR_30 VLAN
ip address 10.100.30.2 255.255.255.0
ip helper-address 10.100.1.22
ip helper-address 10.100.1.78
no ip redirects
no ip unreachables
no ip proxy-arp
standby 30 ip 10.100.30.1
standby 30 priority 105
standby 30 preempt
switch B
interface Vlan30
description CLIENT_FLOOR_30 VLAN
ip address 10.100.30.3 255.255.255.0
ip helper-address 10.100.1.22
ip helper-address 10.100.1.78
no ip redirects
no ip unreachables
no ip proxy-arp
standby 30 ip 10.100.30.1
This will only work if you have VTP (VLAN trunking protocol) setup obviously if you understand this far.
What is happening here is that switch A is the root and switch B is the standby. This is defined by the priority of 105.
Anywhere you see 30 represents the floor, so this VLAN would belong to the 30th floor.
The gateway of the clients on this VLAN is 10.100.30.1. Now 10.100.30.1 is on both switches and it is the HSRP (Hot Standby Router Protocol) address. So the A has a real address of 10.100.30.2 and B has a real address of 10.100.30.3 the virtual or HSRP is 10.100.30.1 and is linked to both switches by the (standby 30 10.100.30.1) command.
I'm just going over the main entries so stuff like no ip (redirect, unreachables, proxy-arp) you can google.
For VLANs the ip helper-address is important b/c broadcast do not cross VLANs (why would anyone want them to?) If you have a DHCP server that is in a SERVER VLAN just setting up the client VLANs and leaving with result in an entire network of workstation trying to find the DHCP server and not able to connect to anything. There are two simple ways to resolve this.
1. setup a DHCP server on every VLAN. This would be the dumbest and most inefficient thing to do.
2. add an ip helper-address statement (ip helper-address 10.100.1.22)to allow the client VLAN to find the server in the SERVER VLAN. 10.100.1.22 would be my DHCP server and this line would be in all my VLAN configs. Not only that but a scope for every client VLAN will have to be created in your DHCP server. So the scope created for the network on the 30th floor would be set to give out IP as such;
10.100.30.100-254 /24.
You can also see that I have another ip helper-address there. That is for another server that uses broadcasts to communicate with the clients.
For the configs above if I had a network that spanned across a 30 floor building I would have a VLAN for every floor that would look the same way. I also have a management VLAN, Server VLAN, Voice VLAN, Video VLAN, Printer VLAN, Wireless VLAN etc...
You can see how complicated this can get and this is only VLANs we are dealing with here.
In the core we have our VLANs. As I explained in a past post each floor is a VLAN. The only way to make this physical redundancy work is to set it up virtually in the core. We have two core switches A&B. One is the root and the other is the standby. If the root core fails for whatever reason the standby is there. The setup on the core for redundant VLANs looks like this.
switch A
interface Vlan30
description CLIENT_FLOOR_30 VLAN
ip address 10.100.30.2 255.255.255.0
ip helper-address 10.100.1.22
ip helper-address 10.100.1.78
no ip redirects
no ip unreachables
no ip proxy-arp
standby 30 ip 10.100.30.1
standby 30 priority 105
standby 30 preempt
switch B
interface Vlan30
description CLIENT_FLOOR_30 VLAN
ip address 10.100.30.3 255.255.255.0
ip helper-address 10.100.1.22
ip helper-address 10.100.1.78
no ip redirects
no ip unreachables
no ip proxy-arp
standby 30 ip 10.100.30.1
This will only work if you have VTP (VLAN trunking protocol) setup obviously if you understand this far.
What is happening here is that switch A is the root and switch B is the standby. This is defined by the priority of 105.
Anywhere you see 30 represents the floor, so this VLAN would belong to the 30th floor.
The gateway of the clients on this VLAN is 10.100.30.1. Now 10.100.30.1 is on both switches and it is the HSRP (Hot Standby Router Protocol) address. So the A has a real address of 10.100.30.2 and B has a real address of 10.100.30.3 the virtual or HSRP is 10.100.30.1 and is linked to both switches by the (standby 30 10.100.30.1) command.
I'm just going over the main entries so stuff like no ip (redirect, unreachables, proxy-arp) you can google.
For VLANs the ip helper-address is important b/c broadcast do not cross VLANs (why would anyone want them to?) If you have a DHCP server that is in a SERVER VLAN just setting up the client VLANs and leaving with result in an entire network of workstation trying to find the DHCP server and not able to connect to anything. There are two simple ways to resolve this.
1. setup a DHCP server on every VLAN. This would be the dumbest and most inefficient thing to do.
2. add an ip helper-address statement (ip helper-address 10.100.1.22)to allow the client VLAN to find the server in the SERVER VLAN. 10.100.1.22 would be my DHCP server and this line would be in all my VLAN configs. Not only that but a scope for every client VLAN will have to be created in your DHCP server. So the scope created for the network on the 30th floor would be set to give out IP as such;
10.100.30.100-254 /24.
You can also see that I have another ip helper-address there. That is for another server that uses broadcasts to communicate with the clients.
For the configs above if I had a network that spanned across a 30 floor building I would have a VLAN for every floor that would look the same way. I also have a management VLAN, Server VLAN, Voice VLAN, Video VLAN, Printer VLAN, Wireless VLAN etc...
You can see how complicated this can get and this is only VLANs we are dealing with here.
Wednesday, July 19, 2006
Cisco phones are in
As I am typing this up I don't even know the exact model number of them LOL. I'll update that when I get the pics of them up.
(update 7941)

My desk area is in shambles. 100 phones in 20 boxes piled up by my desk.

Along with 2 GigE expansion blades for both 4506's a few trunk adapters (I think that's what the box said)

2 routers and a server, voice gateway and call manager (unity server not here yet). I didn't bother check for details been too busy with other things.

Here are the pics.
(update 7941)
My desk area is in shambles. 100 phones in 20 boxes piled up by my desk.
Along with 2 GigE expansion blades for both 4506's a few trunk adapters (I think that's what the box said)
2 routers and a server, voice gateway and call manager (unity server not here yet). I didn't bother check for details been too busy with other things.
Here are the pics.
Monday, July 10, 2006
What's next?
While I was out we got the go ahead to acquire another floor in the building. This floor will accommodate a least 65 users. We will have to core fiber from one of our other floors. We can't drop a patch cable out the window like we did a few years ago this time (true story).
This new floor will get all new cabling and a dual fiber run to our 4506's, PoE switches and Cisco IP phones. We are finally moving over into the IPT boat. It will be a Cisco hybrid and work with our existing Nortel PBX. We will be using a Cisco CallManager 4.0-PBX Interoperability. New toys and new headaches.
I've been doing a lot of Cisco stuff lately. Very fun stuff.
This new floor will get all new cabling and a dual fiber run to our 4506's, PoE switches and Cisco IP phones. We are finally moving over into the IPT boat. It will be a Cisco hybrid and work with our existing Nortel PBX. We will be using a Cisco CallManager 4.0-PBX Interoperability. New toys and new headaches.
I've been doing a lot of Cisco stuff lately. Very fun stuff.
I am back from my month off.
And you thought 2 weeks or even a 3 day weekend went by fast. My month flew like the wind. Some would have tried to squeeze in a mini vacation and travel not me. I was home enjoying fatherhood.
Thursday, June 29, 2006
Taken much needed time off
I've taken a month off from work and all tech related things to raise my daughter. You can tell that I can't sleep by the time I am posting this. She has has changed my sleeping pattern. I'm not sure how I am going to cope with that when I go back to work. We'll see!
Sunday, June 11, 2006
She's here.
At 10:52am my first born arrived. She is so beautiful. The life that I once knew has officially changed. I am a father.
Daddy loves you Maia.
Daddy loves you Maia.
Tuesday, June 06, 2006
Network Upgrade complete! Flawless execution!
On Saturday June 3rd we did our cut over to the new network. This was the true test and all went damn near perfectly. All in all it was still flawless. We had one issue with netbios and one of our CAD applications.
We used an IP Helper address to route all those packets to the license server IP.
The application work where the client needs to find the server and check out license. Once the client gets the license the server seems to need to know if the client still has the license so it can give the next license to the next client. What was happening was that the server was giving out the same license to all clients. Seems like the server was using netbios to look for computer names. I was able to resolve this by adding DNS suffixes to the server and license server was updating not thinking that the clients were giving up the license they were trying to keep. It's a bit confusing reading it here but if you see it in action it will make more sense.
Other than this legacy netbios multi VLAN issue everything else was golden. VPN, email, web, all of our remote sites, databases etc. was all good. I think I mentioned before that we had to change subnets from /16 to /24 so this also meant that some of our servers needed an IP change as well. Those changes were made and everything was updated. I also had to create objects in my checkpoint firewall for every VLAN. I was getting some IP spoofing in the logs and was like WTF! Come to find out the objects weren't created.
If you are attempting to do anything like this make sure you have a checklist and plan, plan, plan. So much for that project. My hat goes off to Dimension Data for their help and support. Thanks Joe!
We used an IP Helper address to route all those packets to the license server IP.
The application work where the client needs to find the server and check out license. Once the client gets the license the server seems to need to know if the client still has the license so it can give the next license to the next client. What was happening was that the server was giving out the same license to all clients. Seems like the server was using netbios to look for computer names. I was able to resolve this by adding DNS suffixes to the server and license server was updating not thinking that the clients were giving up the license they were trying to keep. It's a bit confusing reading it here but if you see it in action it will make more sense.
Other than this legacy netbios multi VLAN issue everything else was golden. VPN, email, web, all of our remote sites, databases etc. was all good. I think I mentioned before that we had to change subnets from /16 to /24 so this also meant that some of our servers needed an IP change as well. Those changes were made and everything was updated. I also had to create objects in my checkpoint firewall for every VLAN. I was getting some IP spoofing in the logs and was like WTF! Come to find out the objects weren't created.
If you are attempting to do anything like this make sure you have a checklist and plan, plan, plan. So much for that project. My hat goes off to Dimension Data for their help and support. Thanks Joe!
Wednesday, May 31, 2006
New Network diagram
Sunday, May 28, 2006
Apple Xserve RAID in a Windows 2003 server environment
We've faced a few storage crisis in the past. The main one being the production data. We have also been faced with archive storage problems. What we use to do years ago was when a project (a huge root folder gigs in size) was ready to be archived we use to in this order;
-make a tape backup and remove the files from the network
-burned a lot of CD's and remove the files from the network
-burned DVD's and remove the files from the network
-copy the project to a NAS device
-copy the project to cheap large IDE/SATA drives
That is a basic timeline of our archive process. This has become very inefficient. Even though everything was properly labeled and could be found it was still inefficient. Why? It could take a long time to search through the amount of single backup tapes, CD's, DVD's and archive locations on the network and NAS devices for a specific piece of data. Also the data was all over the place as you can see.
We resolved these problems by revisiting centralized storage again. An expensive SAN for dead storage is a waste of a lot of money (depending on your environment and your budget). A bunch of cheap storage is also a waste b/c you will be buying A BUNCH of device eliminating the centralization factor. Also when those device get remodeled and decommissioned you are stuck with a bunch of devices of different storage sizes and device shapes and styles. Our choice was Apples Xserve RAID.
We decided on the Apple Xserve RAID after careful research. Our biggest question was b/c it was an apple product will our Windows servers see the storage? Also will our Windows servers see a volume over 2 TB. Windows use to have a 2 TB limit on their volumes. This was back in the early Windows 2000 server days. Then Microsoft came out with Dynamic disks. Where you can use 2 basic disks to create a dynamic disk larger than 2 TB. Read more about it here,Reviewing Storage Limits
After we were confident that our servers will be able to create a volume over 2 TB we placed the order for their 7 TB Xserve RAID. It cost us $13,000. Talk about cheap storage.
The device is by no means a cheap POS though. It has 2 storage processors, 2 fiber connections, 2 power supplies and 14 hot swap Ultra ATA 500GB drives. This is a very nice piece of hardware just like all of apple's hardware products they did not slack on this one. As good as it looks it was even easier to setup. The has 2 of everything including network interfaces. These interfaces are set for DHCP so you just plug the device in and they are on your network. Apple's RAID Admin tool that comes with OS X but they also have a Java based one for Windows environments finds the device on your network. You can now change the IP's of both interface to conform with your server or storage device IP addressing. within in RAID Admin you can manage the device like any other enterprise level storage device. We are not using the Xserve RAID as a true SAN so will are not managing drive space in that manner. We are using it as NAS on steroids or a limited SAN. Why I say that is b/c we have connected the Xserve RAID to our fiber channel switch and zoned it out to it's host server. Our Windows 2003 server detects the Xserve RAID as if it were an internal drive or a SAN drive.
So far the Xserve RAID is working great. After creating the partition in Windows disk manager and waiting 28 hours for the drives to initialize (yes 28 hours) the device has been working flawlessly. Windows 2003 server sees 5.5 TB out of the 7 TB raw so keep that in mind that you will lose 1.5 TB to overhead. We have populated the device with 2.5 TB or archive data so far and we still have a lot of data left to add. Will we needs another one soon? I hope so b/c these device are very nice to have on your network. It just makes managing and centralizing storage so easy, cheap and simple.
Front of Apple Xserve RAID

Back of Apple Xserve RAID
-make a tape backup and remove the files from the network
-burned a lot of CD's and remove the files from the network
-burned DVD's and remove the files from the network
-copy the project to a NAS device
-copy the project to cheap large IDE/SATA drives
That is a basic timeline of our archive process. This has become very inefficient. Even though everything was properly labeled and could be found it was still inefficient. Why? It could take a long time to search through the amount of single backup tapes, CD's, DVD's and archive locations on the network and NAS devices for a specific piece of data. Also the data was all over the place as you can see.
We resolved these problems by revisiting centralized storage again. An expensive SAN for dead storage is a waste of a lot of money (depending on your environment and your budget). A bunch of cheap storage is also a waste b/c you will be buying A BUNCH of device eliminating the centralization factor. Also when those device get remodeled and decommissioned you are stuck with a bunch of devices of different storage sizes and device shapes and styles. Our choice was Apples Xserve RAID.
We decided on the Apple Xserve RAID after careful research. Our biggest question was b/c it was an apple product will our Windows servers see the storage? Also will our Windows servers see a volume over 2 TB. Windows use to have a 2 TB limit on their volumes. This was back in the early Windows 2000 server days. Then Microsoft came out with Dynamic disks. Where you can use 2 basic disks to create a dynamic disk larger than 2 TB. Read more about it here,
After we were confident that our servers will be able to create a volume over 2 TB we placed the order for their 7 TB Xserve RAID. It cost us $13,000. Talk about cheap storage.
The device is by no means a cheap POS though. It has 2 storage processors, 2 fiber connections, 2 power supplies and 14 hot swap Ultra ATA 500GB drives. This is a very nice piece of hardware just like all of apple's hardware products they did not slack on this one. As good as it looks it was even easier to setup. The has 2 of everything including network interfaces. These interfaces are set for DHCP so you just plug the device in and they are on your network. Apple's RAID Admin tool that comes with OS X but they also have a Java based one for Windows environments finds the device on your network. You can now change the IP's of both interface to conform with your server or storage device IP addressing. within in RAID Admin you can manage the device like any other enterprise level storage device. We are not using the Xserve RAID as a true SAN so will are not managing drive space in that manner. We are using it as NAS on steroids or a limited SAN. Why I say that is b/c we have connected the Xserve RAID to our fiber channel switch and zoned it out to it's host server. Our Windows 2003 server detects the Xserve RAID as if it were an internal drive or a SAN drive.
So far the Xserve RAID is working great. After creating the partition in Windows disk manager and waiting 28 hours for the drives to initialize (yes 28 hours) the device has been working flawlessly. Windows 2003 server sees 5.5 TB out of the 7 TB raw so keep that in mind that you will lose 1.5 TB to overhead. We have populated the device with 2.5 TB or archive data so far and we still have a lot of data left to add. Will we needs another one soon? I hope so b/c these device are very nice to have on your network. It just makes managing and centralizing storage so easy, cheap and simple.
Front of Apple Xserve RAID
Back of Apple Xserve RAID
SPAM
Spam use to be a huge issue for me about 3 years ago. We used a software product called mailsweeper. It worked OK but like an anti virus program the definitions had to be updated by us and rules and exceptions had to be put in as well. It was a headache to manage and took focus away from other areas that needed attention. Every Monday or day after a long weekend we would have well over 65,000 emails caught by mailsweeper. It worked good and worked too good sometime. It would also catch a lot of false positives. We had to sift through all the SPAM just to find blocked emails. It was very time consuming.
These days I don't even think about spam. Spam is a word that I forget exist. We have made our entire company very happy when we had MessageLabs (www.messagelabs.com)take over and filter all of our emails. They have a very robust multilayer filtering system. Spam, virus and porn also images with excessive skin content. One of the best features about it is that the user administers their own blocked emails. If an email is a false positive the user will get an email from messagelabs saying they have blocked emails. In the notification email their is a login issued by messagelabs so they can go in a release or delete the email. They also have a retention period so the emails won't pile up in their system.
How it works is you have to edit your MX records with your ISP to send all your SMTP traffic to messagelabs cluster. Messagelabs will give you a virtual IP which is a cluster of towers that will filter you emails. Once messagelabs has your emails they will process it through their filters and then forward it to your mail server IP. If you are watching your firewall log you will see entries for MLtower## sending emails to your email server. Best practice is that you will want to set your email server to only sent emails to messagelabs and also only receive emails from them also. This can be done in your firewall and should be able to be done on you email server as well. I use exchange so it is there.
Spam for us is a thing of the past. If you are still (LOL) having spam issues in your company check out www.messagelabs.com or www.postini.com I can only speak for ML but I hear postini is nice also.
These days I don't even think about spam. Spam is a word that I forget exist. We have made our entire company very happy when we had MessageLabs (www.messagelabs.com)take over and filter all of our emails. They have a very robust multilayer filtering system. Spam, virus and porn also images with excessive skin content. One of the best features about it is that the user administers their own blocked emails. If an email is a false positive the user will get an email from messagelabs saying they have blocked emails. In the notification email their is a login issued by messagelabs so they can go in a release or delete the email. They also have a retention period so the emails won't pile up in their system.
How it works is you have to edit your MX records with your ISP to send all your SMTP traffic to messagelabs cluster. Messagelabs will give you a virtual IP which is a cluster of towers that will filter you emails. Once messagelabs has your emails they will process it through their filters and then forward it to your mail server IP. If you are watching your firewall log you will see entries for MLtower## sending emails to your email server. Best practice is that you will want to set your email server to only sent emails to messagelabs and also only receive emails from them also. This can be done in your firewall and should be able to be done on you email server as well. I use exchange so it is there.
Spam for us is a thing of the past. If you are still (LOL) having spam issues in your company check out www.messagelabs.com or www.postini.com I can only speak for ML but I hear postini is nice also.
Friday, May 26, 2006
Day 3 of our network upgrade - VLANs
Today I just went through and planned out our IP scheme. Like I mentioned before each floor will be it's own VLAN network. Here is how they will be configured;
16th floor VLAN IP
IP scheme 10.100.16.x / 24
Gateway 10.100.16.1
15th floor VLAN IP
IP scheme 10.100.15.x / 24
Gateway 10.100.15.1
14th floor VLAN IP
IP scheme 10.100.14.x / 24
Gateway 10.100.14.1
4th floor VLAN IP
IP scheme 10.100.4.x / 24
Gateway 10.100.4.1
3rd floor VLAN IP
IP scheme 10.100.3.x / 24
Gateway 10.100.3.1
A lot to think about and thanks to EIGRP that takes care of most of it :D
I ran some test on printers and plotters as well (we do a ton of that here) just to be sure that the print servers in one VLAN can communicate with the printers/plotters on another VLAN. We all know it works but you don't want any surprised come cutover time. This is why we test and test and test some more.
On cutover day I have a lot of sensitive work to do. I need to change my netmask from /16 to /24 that means I need to get to all my servers and firewall objects and SAN devices. Those are critical. These are some of things an MIS has to worry about. Yes worry and stress to the point were you almost crap your pants. You ever get those feelings? LOL!
16th floor VLAN IP
IP scheme 10.100.16.x / 24
Gateway 10.100.16.1
15th floor VLAN IP
IP scheme 10.100.15.x / 24
Gateway 10.100.15.1
14th floor VLAN IP
IP scheme 10.100.14.x / 24
Gateway 10.100.14.1
4th floor VLAN IP
IP scheme 10.100.4.x / 24
Gateway 10.100.4.1
3rd floor VLAN IP
IP scheme 10.100.3.x / 24
Gateway 10.100.3.1
A lot to think about and thanks to EIGRP that takes care of most of it :D
I ran some test on printers and plotters as well (we do a ton of that here) just to be sure that the print servers in one VLAN can communicate with the printers/plotters on another VLAN. We all know it works but you don't want any surprised come cutover time. This is why we test and test and test some more.
On cutover day I have a lot of sensitive work to do. I need to change my netmask from /16 to /24 that means I need to get to all my servers and firewall objects and SAN devices. Those are critical. These are some of things an MIS has to worry about. Yes worry and stress to the point were you almost crap your pants. You ever get those feelings? LOL!
Thursday, May 25, 2006
Day 2 of our network upgrade - setting up the routes
Today the consultant and I just went through the design and made sure we had all the routes in place. We are moving from a network that covers 5 floors but is a single flat network (VLAN 1) to a multi VLAN network. Each of the floors will be it's own VLAN. Think of each floor as their own network. With this configuration I need to make sure all clients can connect to each other, the servers and connect to our London and Shanghai networks. Thank God for EIGRP. Without EIGRP our routing table would be at arms length. Meaning that I would have had to tell the router that every VLAN exist, where they are and what path they need to take to get to their destination. I would have to think like a router while entering all of these routes in the routing table. I don't have to do that with EIGRP.
**What is EIGRP?
Enhanced Interior Gateway Routing Protocol (EIGRP) is a Cisco proprietary routing protocol based on their original IGRP. EIGRP is a balanced hybrid IP routing protocol, with optimizations to minimize both the routing instability incurred after topology changes, as well as the use of bandwidth and processing power in the router.
Some of the routing optimizations are based on the Diffusing Update Algorithm (DUAL) work from SRI, which guarantees loop-free operation. In particular, DUAL avoids the "count to infinity" behavior of RIP when a destination becomes completely unreachable. The maximum hop count of EIGRP-routed packets is 224.**
Or just look at the pic to get a better idea of what it is and does.
**What is EIGRP?
Enhanced Interior Gateway Routing Protocol (EIGRP) is a Cisco proprietary routing protocol based on their original IGRP. EIGRP is a balanced hybrid IP routing protocol, with optimizations to minimize both the routing instability incurred after topology changes, as well as the use of bandwidth and processing power in the router.
Some of the routing optimizations are based on the Diffusing Update Algorithm (DUAL) work from SRI, which guarantees loop-free operation. In particular, DUAL avoids the "count to infinity" behavior of RIP when a destination becomes completely unreachable. The maximum hop count of EIGRP-routed packets is 224.**
Or just look at the pic to get a better idea of what it is and does.
Wednesday, May 24, 2006
Day 1 of our network upgrade - Cisco 4506's
We unpacked and placed all the switches in their locations throughout the company. Once we connected the access layer switches to the extra pair of fiber we had to hope we would get a light at the end of the tunnel LOL. No really we had to hope for a light down in the datacenter at the end of the fiber run. When we were done installing the switches we got our lights. Everything went smooth. The new network is running in parallel.
Here is our new core.

2 Cisco 4506's. We will have 2 runs to each access layer switch from the core. This is in preparation for a future VoIP install later on. Your foundation MUST be up to par before you can even think about VoIP.
We are finally moving to a more enterprise level network. Cisco would call it a three-layered hierarchical model or hierarchical internetworking model. It consist of;
-Core layer
-Distribution layer
-Access layer
Our setup will be core/distribution layer (all in the core) and access layer out on the floors.
Here is our new core.
2 Cisco 4506's. We will have 2 runs to each access layer switch from the core. This is in preparation for a future VoIP install later on. Your foundation MUST be up to par before you can even think about VoIP.
We are finally moving to a more enterprise level network. Cisco would call it a three-layered hierarchical model or hierarchical internetworking model. It consist of;
-Core layer
-Distribution layer
-Access layer
Our setup will be core/distribution layer (all in the core) and access layer out on the floors.
Tuesday, May 23, 2006
My Coworker won a MacBook from the apple store in NYC
What a lucky MOFO. If I had won I would have...... given it my fieance or my mother :D. It's funny how he won too. He originally went to the opening and spent 3 hours on line. He got in and IM'ed me at home said he was standing next to celebs and such. Stayed for about an hour and left. He went to hang out on Friday night and went back to the apple store at 5am. Filled out the form and left. He got a call on Sunday saying he won. Congrats!!!

Congrats!
Congrats!
emc Clarion CX300 our storage solution
When we decided to go with a SAN over a year ago we made that decision based on these criteria;
-centralized storage
-redundancy
-easy to manage (if you know what you are doing)
-scalability
-Dell/emc maintenance and support (very good in this area)
-performance
-versatility
We are a Microsoft Windows shop so it was a very easy integration. It took a day to set up and get all the servers configured. Each server needed 2 Host Bus Adapters (HBA), drivers, SANsurfers and emc Powerpath. These are for connectivity management and licensing.
Once the SAN itself was unboxed, racked and firmware was updated it was time to carve it up. Originally we only have the CX300 itself and 1 disk array Enclosure (DAE) we added a second one a few months later. I have a pic of how the LUNs carved up look in paper.

**What are LUNs?
In computer storage, a logical unit number or LUN is an address for an individual disk drive and by extension, the disk device itself. The term originated in the SCSI protocol as a way of differentiating individual disk drives within a common SCSI target device like a disk array.
The term has become common in storage area networks (SAN) and other enterprise storage fields. Today, LUNs are normally not entire disk drives but rather virtual partitions (or volumes) of a RAID set.(wikipedia definition)**
After the carving we were ready to connect the server to the SAN via McData Fiber Channel switches. Here we had to do zoning.
**What is SAN zoning?
SAN zoning is a method of arranging Fiber Channel devices into logical groups over the physical configuration of the fabric.
(seems like this is the best used definition on the web so why reinvent the wheel ;) )**
Zoning on the McData switches are really easy once you get the hang of it. Find the servers WW name and find the storage device WW name and add the two to the same field. This will allow the Windows server to detect a new storage device in disk manager after you point the server to it's LUN on the SAN using emc Navisphere. No rebooting required if all works right. Hit refresh a few times and your new volumes is ready to be partitioned and formatted.
Here is a diagram of the server/SAN setup.

(I'll talk about the apple XServeRAID in a bit)
Seems easy enough but I didn't do it alone. We had the Dell/emc guy with us the whole time. They won't let you perform these task without an engineer onsite. Too easy for something to go wrong.
The benefit of all this is that if my server runs out of space I can easily grow the LUN and manage everything from a single location. Centralized storage is a must in our environment. As much as we want to centralize everything we still can't :/
-centralized storage
-redundancy
-easy to manage (if you know what you are doing)
-scalability
-Dell/emc maintenance and support (very good in this area)
-performance
-versatility
We are a Microsoft Windows shop so it was a very easy integration. It took a day to set up and get all the servers configured. Each server needed 2 Host Bus Adapters (HBA), drivers, SANsurfers and emc Powerpath. These are for connectivity management and licensing.
Once the SAN itself was unboxed, racked and firmware was updated it was time to carve it up. Originally we only have the CX300 itself and 1 disk array Enclosure (DAE) we added a second one a few months later. I have a pic of how the LUNs carved up look in paper.
**What are LUNs?
In computer storage, a logical unit number or LUN is an address for an individual disk drive and by extension, the disk device itself. The term originated in the SCSI protocol as a way of differentiating individual disk drives within a common SCSI target device like a disk array.
The term has become common in storage area networks (SAN) and other enterprise storage fields. Today, LUNs are normally not entire disk drives but rather virtual partitions (or volumes) of a RAID set.(wikipedia definition)**
After the carving we were ready to connect the server to the SAN via McData Fiber Channel switches. Here we had to do zoning.
**What is SAN zoning?
SAN zoning is a method of arranging Fiber Channel devices into logical groups over the physical configuration of the fabric.
(seems like this is the best used definition on the web so why reinvent the wheel ;) )**
Zoning on the McData switches are really easy once you get the hang of it. Find the servers WW name and find the storage device WW name and add the two to the same field. This will allow the Windows server to detect a new storage device in disk manager after you point the server to it's LUN on the SAN using emc Navisphere. No rebooting required if all works right. Hit refresh a few times and your new volumes is ready to be partitioned and formatted.
Here is a diagram of the server/SAN setup.
(I'll talk about the apple XServeRAID in a bit)
Seems easy enough but I didn't do it alone. We had the Dell/emc guy with us the whole time. They won't let you perform these task without an engineer onsite. Too easy for something to go wrong.
The benefit of all this is that if my server runs out of space I can easily grow the LUN and manage everything from a single location. Centralized storage is a must in our environment. As much as we want to centralize everything we still can't :/
Storage, one of he biggest headaches to deal with in this environment.
I work for an architecture firm in NYC where we generate lots of large files. Files from various 3d, CAD and imaging applications. In this environment is is hard to manage the storage. Why? Well here is why.
When a project starts a folder is created in on the file server. This folder has a name or number associated with it to identify the project. For the life of the project everything related to it is stored here (accept emails). These projects last years. I really mean years. Well if you think about it how long does it take to build lets say (for example) a Dam or a Skyscraper. This is how long these files have to be accessible on the network. If the project is active it has to be on the production server. If it's on hold or wrapped up it goes to the archive server. These project folders get to be well over 100GB and that is only 1 of many projects.
Why can't I just delete old files?
That's not my job to be honest. Sounds like a don't care attitude right? Wrong! If I went the lengths to delete every old file even though they are on tape backup I will be restoring files EVERY DAY all day long. It should not fall on my to be in charge of what gets deleted and what doesn't that should be the team that is in charge of the projects job. I only provide the means for them to store their files and work without problems. Nice cop out right ;)
So I and my team of admins have been faced with this problem of the servers filling up year after year. How we use to deal with it was throw disk at the server. At one point we had about 5 files servers of various sizes filling up. One year I thought I was in the clear. We had a 400GB volume on our main file server and it filled up. We purchased an 800GB drive cage for an HP server. So I think to myself and tell my boss we are in the clear for the next 2 years. Well 6 months go by and the 800GB is down to 100GB free. We move inactive projects off to free up space and this goes on for a few more months. We then double that capacity. At the time 800GB was a hell of a lot of space for our size company. When we filled it up I was as shocked as anyone else would be. So now we had 1.6TB. Again we filled that up in 18 months. So in 2 years we ran through over 2 TB (if you include the projects we pulled off to make space). We decide to get an emc CX300 with 2TB production and 4TB for archive. This working out OK for since we got it but we still are running out a space.
We are currently looking for a hierarchical storage management (HSM) solution that integrates well in our environment. No it's not easy to just go get IBM Tivoli, CommVault or Veritas Enterprise Vault <--- (we have this for email and what a pain in the ass it is to set up). We have to make sure that whatever pointer file is left behind can be read by our CAD software. The problem is that our CAD software uses what is called an Xref. An Xref is a bunch of files that are accossiated with the main file you are working on. If I open file building1234.dwg it can call dozens of other files and they will all open due to the Xref. This is the root of the storage problem and the cause behind why a solution isn't easy to find. Say we use an HSM solution to move files older than 30 days to an archive spot, leaving a pointer in place and that file moved is a part of an Xref. If my CAD software cannot read that pointer file we can potentially corrupt the main file and delay a project. I have been explaining to these vendors this situation giving the same example asking them to find out if these HSM products will work with CAD software. Ofcourse they don't test nothing and say yeah it should work so I can buy it. Well if the software costed $30 I would buy it and try it but they cost thousands of dollars. We all know these software works on word files and all the common stuff that you find in the financails, law and medical firms but the architecture firms are always left out. It's like no one knows about us. Maybe we should stop designing buildings.
When a project starts a folder is created in on the file server. This folder has a name or number associated with it to identify the project. For the life of the project everything related to it is stored here (accept emails). These projects last years. I really mean years. Well if you think about it how long does it take to build lets say (for example) a Dam or a Skyscraper. This is how long these files have to be accessible on the network. If the project is active it has to be on the production server. If it's on hold or wrapped up it goes to the archive server. These project folders get to be well over 100GB and that is only 1 of many projects.
Why can't I just delete old files?
That's not my job to be honest. Sounds like a don't care attitude right? Wrong! If I went the lengths to delete every old file even though they are on tape backup I will be restoring files EVERY DAY all day long. It should not fall on my to be in charge of what gets deleted and what doesn't that should be the team that is in charge of the projects job. I only provide the means for them to store their files and work without problems. Nice cop out right ;)
So I and my team of admins have been faced with this problem of the servers filling up year after year. How we use to deal with it was throw disk at the server. At one point we had about 5 files servers of various sizes filling up. One year I thought I was in the clear. We had a 400GB volume on our main file server and it filled up. We purchased an 800GB drive cage for an HP server. So I think to myself and tell my boss we are in the clear for the next 2 years. Well 6 months go by and the 800GB is down to 100GB free. We move inactive projects off to free up space and this goes on for a few more months. We then double that capacity. At the time 800GB was a hell of a lot of space for our size company. When we filled it up I was as shocked as anyone else would be. So now we had 1.6TB. Again we filled that up in 18 months. So in 2 years we ran through over 2 TB (if you include the projects we pulled off to make space). We decide to get an emc CX300 with 2TB production and 4TB for archive. This working out OK for since we got it but we still are running out a space.
We are currently looking for a hierarchical storage management (HSM) solution that integrates well in our environment. No it's not easy to just go get IBM Tivoli, CommVault or Veritas Enterprise Vault <--- (we have this for email and what a pain in the ass it is to set up). We have to make sure that whatever pointer file is left behind can be read by our CAD software. The problem is that our CAD software uses what is called an Xref. An Xref is a bunch of files that are accossiated with the main file you are working on. If I open file building1234.dwg it can call dozens of other files and they will all open due to the Xref. This is the root of the storage problem and the cause behind why a solution isn't easy to find. Say we use an HSM solution to move files older than 30 days to an archive spot, leaving a pointer in place and that file moved is a part of an Xref. If my CAD software cannot read that pointer file we can potentially corrupt the main file and delay a project. I have been explaining to these vendors this situation giving the same example asking them to find out if these HSM products will work with CAD software. Ofcourse they don't test nothing and say yeah it should work so I can buy it. Well if the software costed $30 I would buy it and try it but they cost thousands of dollars. We all know these software works on word files and all the common stuff that you find in the financails, law and medical firms but the architecture firms are always left out. It's like no one knows about us. Maybe we should stop designing buildings.
Thursday, May 11, 2006
Best App
Google Earth
Currently using it to find my next home. Get the address of the property of interest (not always provided on certain real estate sites). Plug the address into Google Earth and you can have an idea of what the neighborhood looks like. You can also get an idea of the lot size without having to visit the property. And you can get an idea of the distance your new home will be in proximity to certain landmarks, malls, super market, theaters, schools, your job, hospital, police, transportation etc. This is how I am currently using Google Earth. What's yours?
Currently using it to find my next home. Get the address of the property of interest (not always provided on certain real estate sites). Plug the address into Google Earth and you can have an idea of what the neighborhood looks like. You can also get an idea of the lot size without having to visit the property. And you can get an idea of the distance your new home will be in proximity to certain landmarks, malls, super market, theaters, schools, your job, hospital, police, transportation etc. This is how I am currently using Google Earth. What's yours?
Subscribe to:
Posts (Atom)